🐤 CuboAi Tip:

1. For a smooth setup experience, please download the CuboAi App and create an account before assembling the stand or connecting CuboAi/CuboAi Plus to a power source.

2. If you are unsure which model you have, you may check the location of the multi-purpose button.

- CuboAi Plus's multi-purpose button is located on the back of the baby monitor
- CuboAi's multi-purpose button is located on the side of the baby monitor

3. The height of the CuboAi baby monitor is ~ 4.3” / 11cm

4. Please refer to the Quick Start Guide - 3 Stand Set or Quick Start Guide - Wall Mount Set / Quick Start Guide - CuboAi for instructions on how to assemble. 

• CuboAi Plus
• CuboAi

• CuboAi Plus

🐤 CuboAi Tip: Before connecting CuboAi Plus to power, please make sure to connect the Temperature & Humidity Dongle between the baby monitor and the cable to make sure CuboAi Plus shows the Temperature & Humidity readings properly in the CuboAi App.

1. Crib Mount (to be used with 3m cable): It is designed to attach to the spindles of Baby's crib.

- The Crib Mount needs to be used with the U-Shaped Camera Holder, L-Shaped Stand Element, Stand Elements & Connectors.

- The Crib Mount can only be used between spindles that are at most 2.7” / 7 cm apart. Made out of a material similar in texture to a yoga mat, the clamping bed attachment slides in between two spindles of a crib, enabling the stand to fit snugly into many different-sized cribs. 

- It is recommended to install the crib attachment under the bed board/bottom of the railing)

- Crib Mount Height: 7.1" / 18cm: The CuboAi Plus' height can be adjusted by changing the position of the bed clamp. This saves space and can be transported with the crib for convenience.

- Please refer to Setting up your CuboAi Plus: Crib Mount to assemble the stand.

2. Floor Stand (to be used with 3m cable):

- The Floor Stand needs to be used with the U-Shaped Camera Holder, L-Shaped Stand Element, Stand Elements & Connectors. (The assembled stand height is ~ 4'5" / 135cm)

- This can be used when Baby grows out of their crib since it does not require attachment.

- The Floor Stand was designed to freely move around as needed. Once assembled, Please slide the entire base of the floor stand under the crib (as pictured below) to maintain the balance and stability of the stand. 

- The Floor Base Height is 2” / 5cm, Diameter is 11.4” / 29cm 

- Please refer to Setting up your CuboAi Plus: Floor Stand to assemble the stand.

3. Mobile Stand  (to be used with 2m cable)

 - It is a small docking station for CuboAi Plus attached to a ~7 ft. (200cm) long cord.

- This stand is designed for when you're on the go, whether you’re traveling or just want to set up in a different room of the house. You can bring our CuboAi Travel Case to go traveling.

- This mobile stand also turns CuboAi Plus into a toddler cam when your little one starts crawling or walking around the house!

- Please refer to Setting up your CuboAi Plus: Mobile Stand to assemble the stand.

4. Wall Mount (to be used with 3m cable)

- It is suitable for mounting on cement, wooden, hollow, or dry walls. You will be required to drill a hole in the wall. 

- Tools required: electric drill and 5.5mm (7/32") drill bit, Phillips screwdriver, mallet (optional).

- The wall mount option allows the CuboAi Plus to be mounted directly onto the wall, which helps to save space. 

- Please refer to Setting up your CuboAi Plus: Wall Mount to assemble the stand.

• CuboAi

1.  Crib Attachment

- It is designed to attach to the spindles of Baby's crib. Note that the gap between spindles should be less than 2.7” / 7cm. Made out of a material similar in texture to a yoga mat, the clamping bed attachment slides in between two spindles of a crib, enabling the stand to fit snugly into many different-sized cribs.

- CuboAi’s height can be adjusted by changing the position of the bed clamp. This saves space and can be transported with the crib for convenience.

- Stand Height: 4’3” / 130cm including CuboAi 4.33” / 11cm.

- Please refer to Setting up your CuboAi: Crib Attachment (Gen 1) to assemble the stand.

2. Floor Stand

- It stands on the floor and has a tall neck (about 5 feet) on top of which CuboAi sits. This can be used when Baby grows out of their crib since it does not require attachment.

- The Floor Stand was designed to freely move around as needed. Once assembled, the Floor Stand base can be slid under the crib.
- Stand Height: 5’4” / 163cm including CuboAi (4.33” / 11cm)

- Base Diameter: 11.4” / 29cm, Base Height: 2.16” / 5.5cm
- Please refer to Setting up your CuboAi: Floor Stand (Gen 1) to assemble the stand.


3. Mobile Stand

- It is a small docking station for CuboAi attached to a ~7 ft. (200cm) long cord.

- This stand is designed for when you're on the go, whether you’re traveling or just want to set up in a different room of the house.

- This mobile stand also turns CuboAi into a toddler cam when your little one starts crawling or walking around the house!

- Please refer to Setting up your CuboAi: Mobile Stand (Gen 1) to assemble the stand.

🐤CuboAi Reminder: CuboAi should only be plugged into a power source after being properly and securely attached to a stand. You can confirm that CuboAi is plugged in properly by checking the status light on the multi-purpose button. When CuboAi is starting up, you will see an aqua blue status light. The status light will turn green once CuboAi is in Setup Mode and ready for pairing!

Examples:

There should be no gap between CuboAi and the U-shaped Camera Holder/Mobile Dock when it’s properly attached.

If there is a gap between your baby monitor and the stand, CuboAi will not be able to function regularly. Please make sure you hear a click after putting on the baby monitor to ensure stable connection and device security.

Customer Support Contact Information:

• In-App:  Settings -> Chat with Us
• Facebook Messenger: m.me/cubobabymonitor
• Email: support@cuboai.com